HPE1-H05 시험 - HP실제시험문제와 답 - 100문항

Question No : 1

A customer needs to decommission a set of HPE ProLiant Gen11 servers that were used for sensitive R&D data. The security policy requires an audit-compliant "Sanitization" of all internal storage and non-volatile memory before the servers leave the facility.
Which iLO 6 feature allows you to automate this complete system wipe with a single action?

A.System Recovery Set "Factory Reset"
B.Intelligent Provisioning "Disk Wipe" utility
C.Format NAND (via CLI)
D.HPE One Button Secure Erase

정답:

Question No : 2

Which specific data reduction behavior is a characteristic of the HPE Alletra 6000 (CASL) architecture compared to the Alletra 9000?

A.It performs deduplication only as a post-process task at night.
B.It compresses data strictly after it lands on the SSDs.
C.It uses "Variable Block" deduplication inline.
D.It relies on hardware offload cards for all compression.

정답:

Question No : 3

In a Hands-On practical task, you are asked to provision a new Volume on an HPE Alletra 9000 using the Data Services Cloud Console. You need to ensure the volume is exported to a specific host. You navigate to the "Block Storage" service.
What is the correct order of operations?

A.Create Volume -> Create Host -> Export Volume to Host.
B.Scan for LUNs -> Format Drive.
C.Create Host Group -> Create Volume.
D.Export Volume -> Create Host.

정답:

Question No : 4

You are diagnosing a severe performance degradation in an AI training cluster utilizing RoCE v2 networking. The issue appears as random latency spikes during the "All-Gather" phase. You inspect the upstream switch and see a high counter for "PFC Storm" and "Head-of-Line Blocking".
What is the specific architectural root cause of this congestion?

A.The GPU servers are using NVMe/TCP instead of RoCE, causing TCP window exhaustion.
B.The "Global Pause" frames are enabled on the switch ports instead of "Priority Flow Control" (PFC).
C.The switch buffer profile is set to "Store-and-Forward" instead of "Cut-Through".
D.The ConnectX-6 NICs are using the wrong firmware version.

정답:

Question No : 5

A customer wants to reduce their Scope 2 Carbon Emissions. They are viewing the HPE GreenLake Sustainability Dashboard and see a metric labeled "Carbon Intensity" (gCO2eq/kWh). They ask how HPE GreenLake derives this specific value for their on-premises data center.
What is the source of this data?

A.It is measured directly by sensors in the HPE Power Supply units.
B.It is calculated based on the user-defined geographic location of the data center and the local power grid's published emission factors.
C.It is retrieved from the iLO "Carbon Footprint" page.
D.It is a static global average applied to all servers.

정답:

Question No : 6

A customer is comparing connection protocols for their new AI training cluster. They need the absolute lowest possible latency for GPU-to-GPU communication between nodes. Cost is a secondary factor.
Which network protocol and adapter configuration should you recommend over standard iSCSI?

A.100GbE/200GbE with RoCE v2 (RDMA over Converged Ethernet)
B.25GbE with TCP Offload Engine (TOE)
C.10GbE Base-T
D.32Gb Fibre Channel

정답:

Question No : 7

An administrator needs to expand the capacity of an HPE Alletra Storage MP B10000 system by adding a new NVMe Drive Enclosure (JBOF). The system is currently online and serving production I/O.
What is the expected behavior when the new enclosure is cabled to the backend switch fabric?

A.The backend switches must be re-zoned manually to allow the controllers to see the new NVMe targets.
B.The system automatically creates a new separate Data Reduction Pool for the new cage; it cannot be merged with the existing pool.
C.The system automatically discovers the new enclosure, but you must manually "Admit" the new drives to the pool to start using them.
D.The system must be powered down to recognize the new enclosure I

정답:

Question No : 8

You have installed a new third-party PCIe accelerator card into an HPE ProLiant DL380 Gen11 server. Upon powering on, the server halts POST with a "Security Violation: PCI Device Failed Authentication" error and refuses to boot. The system is configured with "Production Mode" security.
What technology is actively blocking this device?

A.TPM 2.0
B.Secure Boot
C.Intel SGX
D.SPDM (Security Protocol and Data Model)

정답:

Question No : 9

An administrator notices that the "UID" (Unit Identification) LED on the front of an Alletra MP Drive Enclosure is flashing Blue.
What does this specific LED state indicate?

A.The enclosure is in "Sleep" mode.
B.The enclosure has a critical fault (Power/Fan).
C.The enclosure is currently performing a firmware update.
D.A remote administrator has activated the "Locate" function to identify the specific chassis in the rack.

정답:

Question No : 10

You run a "Firmware Compliance" report in HPE OneView for a group of servers assigned to the "Production-2023" baseline. One server shows a status of "Unknown" for its firmware compliance.
What is the most likely technical reason for this missing data?

A.The server is powered off.
B.The server has not been powered on since the profile was assigned, or the OS has not booted to load the AMS/SUT agents required to inventory the installed drivers.
C.The server does not have an iLO Advanced license.
D.The SPP repository is offline.

정답:

Question No : 11

You are designing a "Secure Boot" policy for a fleet of HPE ProLiant Gen11 servers. The customer wants to ensure that if a bootloader is signed by a Microsoft key that has been publicly revoked due to a vulnerability (like the "BlackLotus" UEFI bootkit), the server will refuse to boot it.
Which database in the Secure Boot architecture is responsible for holding these revoked signatures?

A.DB (Allowed Signature Database)
B.PK (Platform Key)
C.KEK (Key Exchange Key)
D.DBX (Forbidden Signature Database)

정답:

Question No : 12

You are adding a new HPE Synergy frame to an existing Logical Interconnect Group (LIG) to expand the fabric. The existing frame uses HPE Virtual Connect SE 100Gb F32 Modules. You have some spare HPE Virtual Connect SE 40Gb F8 Modules available and attempt to install them in the new frame to save cost, intending to link them to the same master ring.
Why does OneView block this configuration?

A.The 40Gb F8 modules do not support "Master" mode, only "Satellite" mode.
B.The F8 modules use a different connector type (QSFP+) than the F32 (QSFP28).
C.You cannot mix different speeds (100Gb and 40Gb) within the same Logical Interconnect Group.
D.The F8 modules require a "Legacy" LIG type which is incompatible with Image Streamer.

정답:

Question No : 13

You are replacing the "System Battery" (CMOS CR2032) on an HPE ProLiant Gen11 server. After replacing the battery and powering on, the system halts with a "Time Not Set" error. You enter the BIOS to set the time.
What other critical security setting stored in NVRAM might have been reset to default or lost, requiring verification?

A.The BIOS Administrator Password.
B.The OneView Profile association.
C.The iLO IP Address.
D.The RAID configuration on the Smart Array controller.

정답:

Question No : 14

A database administrator asks you to guarantee that their "Month-End Reporting" job will always get at least 5000 IOPS, even if the storage array is under heavy load from backups.
Which QoS feature specifically addresses this need?

A.IOPS Min (Floor)
B.Burst IOPS
C.IOPS Limit (Ceiling)
D.Adaptive Optimization

정답:

Question No : 15

You are managing a Hyper-V cluster profile in HPE OneView. You need to add a new VLAN to all nodes in the cluster. You update the "Logical Interconnect Group" (LIG) to include the new network. After saving, you notice the Logical Interconnect status changes to "Inconsistent".
What action must be taken to make the new VLAN available to the server downlinks?

A.Update the Logical Interconnect from the Group.
B.Update each Server Profile individually to add the network.
C.Delete and recreate the Uplink Set.
D.Reboot the Synergy Composer.

정답:

HP HPE1-H05 시험