Cisco 350-601 問題練習

Question No : 1
Refer to the exhibit.



A network engineer must use a Cisco on-box Python CLI to configure the BGP AS 65501 on Cisco Nexus 9000 Series Switch The output from the command must be returned as raw output instead of JSON format.
Which command set must be used to complete the configuration?

• A.Option A
• B.Option B
• C.Option C
• D.Option D

答えを確認する

正解:

Question No : 2
An engineer must tune an FCIP connection over WAN between two Cisco MDS 9000 Series Switches The customer has determined that default TCP parameters do not function for the link with 300 ms latency.
The TCP profile must Modify the TCP retransmit time to satisfy the WAN latency.
Set the TCP keepalive timeout to 15 seconds.
Set the maximum number of TCP retransmissions to 5
Which command set meets the requirements?

• A.Option A
• B.Option B
• C.Option C
• D.Option D

答えを確認する

正解:

Question No : 3
An engineer must analyze packets arriving from a server port on a Cisco Nexus 9000 Series Switch. The packet sniffer is located on a different switch from the one the server is currently connected to.
The packet capture must meet these requirements:
- It must capture all incoming packets on the switch port.
- It must capture the first 1000 bytes of the packet to conserve bandwidth.
Which action must be taken to meet these requirements?

• A.Configure the marker-packet to 1000.
• B.Implement an ACL with the packet-length of 1000.
• C.Enable the MTU size of 1000.
• D.Set rate-limiting to 1000.

答えを確認する

正解:

Question No : 4
Refer to the exhibit.



Cisco Fabric Services is enabled in the network.
Which type of IP address is used by the Cisco Fabric Services protocol?

• A.IPv4 unicast address
• B.IPv4 multicast address
• C.IPv4 gateway address
• D.IPv4 anycast address

答えを確認する

正解:

Question No : 5
Refer to the exhibit.



An engineer must perform an initial configuration of VXLAN Tunnel End-Point functionality on the Cisco Nexus 9000 Series platform All the necessary features are already enabled on the switch.
Which configuration set must be used to accomplish this goal?

• A.Option A
• B.Option B
• C.Option C
• D.Option D

答えを確認する

正解:

Question No : 6
An engineer needs to install a new package on a Cisco Nexus 9000 Series Switch.
What is the impact of running the install commit <filename> command on the switch?

• A.The previous package that was n use is deleted from bootflash.
• B.The package is used in the running configuration
• C.The package is used after the switch is restarted
• D.The switch is restarted after the upgrade is complete

答えを確認する

正解:

Question No : 7
DRAG DROP
Drag and drop the steps on the left onto the order that they must be implemented on the right to recover a fabric interconnect when there is no working image on the boot flash.

答えを確認する

正解:

Question No : 8
Which storage solution allows multiple users to access files directly on a storage array over a LAN network?

• A.network file system
• B.network-attached storage
• C.direct attached storage
• D.storage area network

答えを確認する

正解:

Question No : 9
DRAG DROP
Refer to the exhibit.



The server is sending traffic to the storage server using Fiber Channel protocol. The requirement is for the N5K-1 to forward traffic to MDS9k-1.
Drag and drop the configuration steps from the right to complete the configuration for N5K-1 on the left. Not all configuration steps are used.

答えを確認する

正解:


Explanation:
npv enable, switchport mode F, interface fc2/1, switchport mode NP

Question No : 10
Refer to the exhibit.



An engineer monitors ingress traffic from Host-A and all traffic for VLAN 20 from Host-B.
Which configuration must be implemented to monitor and export traffic to Network Analyzer?

• A.Option A
• B.Option B
• C.Option C
• D.Option D

答えを確認する

正解:

Question No : 11
Refer to the exhibit.



The network management system that is located at 192.168.10.10 and port 2000 must receive traps from the Cisco UCS Manager called UCSM. The community name is Cisco123! and the SNMP version must be the most secure.
These two commands have already been configured on Cisco UCSM.
UCS-A# scope monitoring
UCS-A/monitoring # enable snmp
Which command set completes the SNMP configure

• A.Option A
• B.Option B
• C.Option C
• D.Option D

答えを確認する

正解:

Question No : 12
What is a characteristic of the NFS protocol?

• A.It is used for booting Cisco UCS B-Series servers.
• B.It is used to access a storage array at a block level.
• C.It uses UDP and HTTP as its transport.
• D.It uses remote procedure calls with TCP/IP for transport.

答えを確認する

正解:

Question No : 13
An engineer implements an environment with multiple traffic types on a consolidated I/O link between Cisco Nexus 9000 Series Switch and MDS 9000 Series Switch.
The configuration must meet these requirements:
• The unified I/O link must support LAN and SAN traffic.
• A single, multipurpose Ethernet transport must be used.
• The configuration must discard MAC addresses that are not part of the current fabric.
• The QoS markings must be preserved.
Which configuration set meets the requirements?

• A.Option A
• B.Option B
• C.Option C
• D.Option D

答えを確認する

正解:

Question No : 14
An engineer must Implement a Python script to manage Cisco Application Centric Infrastructure (ACI) and endpoint groups.
Which Python libraries must be used to parse responses and send requests to Cisco ACI?

• A.Element Tree and SSL
• B.JSON and EtementTree
• C.JSON and requests
• D.socket and JSON

答えを確認する

正解:

Question No : 15
A network engineer must create an EEM script that saves a copy of the running configuration on boot flash and writes a message to syslog when a user saves the configuration to a Cisco Nexus switch.
Which configuration set should be applied to complete this task?

• A.Option A
• B.Option B
• C.Option C
• D.Option D

答えを確認する

正解: